Kavan GO-1088MGW (0.125s/60°, 74kg.cm)

Kavan GO-1088MGW (0.125s/60°, 74kg.cm)Kavan GO 1088MGW (0. 125s 60, 74kg. cm) GO 1088MGW is programmable using the KAVAN GO servo USB programmer interface and PC software. Programmable Functions Servo Angle: Maximal servo rotation angle range setting. The default range is ca 120 within the regular RC signal pulse width range (900~2100 s); ca 180 within the max. signal pulse width range (500~2500 s). Servo Neutral: Servo neutral (centre) position setting. Damping Factor: Servo damping

• Kavan GO-1088MGW (0.125s/60°, 74kg.cm)

• GO-1088MGW is programmable using the KAVAN GO servo USB programmer/interface and PC software.

  Programmable Functions

  • Servo Angle: Maximal servo rotation angle range setting. The default range is ca 120° within the regular RC signal pulse width range (900~2100 µs); ca 180° within the max. signal pulse width range (500~2500 µs).
  • Servo Neutral: Servo neutral (centre) position setting.
  • Damping Factor: Servo damping setting – adjust the characteristics of the servo when stopping.
  • PWM Power: Adjusts the servo output power. The higher the power, the higher the speed and torque of the servo – indeed also the current consumption will be higher.
  • Sensitivity: Servo sensitivity (Dead Band) setting. The higher sensitivity the narrower the dead band – servo moves only if the change of the signal pulse width is bigger than the dead band width. Too high setting may cause servo jitter in some applications. Range: Ultra High (ca 1 µs dead band) – High (ca 2 µs) – Medium (ca 3 µs) – Low (ca 4 µs)
  • Soft Start: Turns on/off the soft start feature. If ON, the servo goes slowly to the initial position corresponding to the servo signal once the power is switched on.
  • Reverse: Reverses the servo movement direction.
  • Narrow Band: FUTABA SR Mode – only for use with FUTABA radio channels working in the SR mode. Do not turn the option on if you are using a different setting of your FUTABA radio or any other radio.
  • SANWA SSR: SANWA SSR Mode - only for use with SANWA radio channels working in the SSR mode. Do not turn the option on if you are using a different setting of your SANWA radio or any other radio.
  • Lost PPM Protection (Fail-Safe): In the case the control signal from the receiver is lost completely or cannot be decoded correctly (due to interference) the servo can use choose one of three fail-safe modes:
  • (a) Release: No fail-safe protection.
  • (b) Keep Position: Keeps the position corresponding to the last correct control signal.
  • (c) Go Neutral Position: The servo returns to the neutral (1500 µs pulse width) position.
  • Over Load protection: Enables or disables overload protection of the servo in three levels – once the overload conditions last for the pre-set time (in seconds), the output power of the servo is reduced to the corresponding pre-set level (% of the max. power).
  • Default: Restores the factory default setting of the connected servo.

  Wide input voltage range 4.8-8.4 V (nominal).

  25T/5.92 mm output shaft.

  Servo dimensions	Standard
  Servo type	Digital
  Programmable	Yes
  Thrust at 4.8V [kg∙cm]	45
  Thrust at 6.0V [kg∙cm]	55
  Thrust at 7.4V [kg∙cm]	65
  Thrust at 8.4V [kg∙cm]	74
  Speed at 4.8V [s/60st.]	0.19
  Speed at 6.0V [s/60st.]	0.165
  Speed at 7.4V [s/60st.]	0.135
  Speed at 8.4V [s/60st.]	0.125
  Servo gears	Metal
  Ball bearings	4x
  High-voltage	Yes
  Power supply [V]	4.8 - 8.4
  Length [mm]	40
  Width [mm]	20
  Height [mm]	38
  Weight [g]	85
  Intended for	Aeroplanes,Helicopters,On-road cars,Off-road cars,Sailing boats,Boats
  Water resistance	Waterproof