Pay in installments of $3.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 18 - Jul 23
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
V20 Portable Keychain Light Rechargeable Bright Mini Flashlight1. Wide range of applications, the side light has a multi color light source, suitable for a variety of scenes 2. The body is made of high quality PC + aluminum alloy, even if accidentally dropped, can still work normally 3. Built in 1100mAh high capacity lithium polymer rechargeable battery, longer battery life 4. Thin and compact, no burden on the trip, out of the bag or carry with you are very lightweight 5. Intelligent dustproof, waterproof,
1. Wide range of applications, the side light has a multi-color light source, suitable for a variety of scenes
2. The body is made of high quality PC + aluminum alloy, even if accidentally dropped, can still work normally
3. Built-in 1100mAh high-capacity lithium polymer rechargeable battery, longer battery life
4. Thin and compact, no burden on the trip, out of the bag or carry with you are very lightweight
5. Intelligent dustproof, waterproof, outdoor use without fear of bad weather
6. When in danger or emergency long press the side light button, immediately sound a high-decibel beeping sound and red and blue lights flashing
7. The lamp can be rotated 180 degrees to meet the needs of multi-angle lighting
8. The tail comes with a magnetic effect, can be quickly attached to the flashlight on the surface of iron objects, release your hands
Parameters:
1. Lighting distance: 100 meters
2. Bulb type: white 351B x 2 + 3535 red x 2; side light: white + green + blue + violet + red
3. Lumen: 1000 lumens
4. Charging interface: Type-C USB
5. Charging display: charging red light, full green light
6. Dual switch design: extremely bright (long press the main light switch button to turn on and off) 1000LM
7. Main light button mode: double click switch; energy saving - low light - medium light - high light - long press off
8. Side light button mode: double-click switch: white light-violet light-green light-red light-blue light-red light flash-red and blue light flash cycle, long-press shutdown; side light button continuously press 3 strikes-main light red light-long-press shutdown; side light button long-press buzzer + red and blue light flash
9. Charging voltage: 5V/1A
10. Tube body quality: PC + aluminum alloy
11. Charging time: 2.5-3 hours; battery life: 3.5-33 hours
12. Battery capacity: 1100mAh
13. Waterproof rating: IP67
14. Size: 69 x 38 x 16mm
15. Weight: 57g
Specification:
| Package Weight |
|
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 18 reviews
Sort
Product Reviews
★★★★★ 5
Saves So Much Time, Perfect Fit On Mercruiser Pre-Alpha Outdrive.
This is a very useful kit. Perfect fit to exchange and align the gimbal bearing on a Mercruiser MR/Pre-Alpha Outdrive. The metal rods are strong and well machined to fit the gimbal bearing and the template lines up great with the housing studs. The overall production quality is very good. Great value because the tools are very durable but for me the biggest value is the time saved. I had the bearing out in about 10 minutes. The ability to line up the bearing before attempting to attach the outdrive upper gear unit is very convenient and saves so much time. This are simple tools, very easy to use.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 1, 2026
★★★★★ 5
Easy to use
Works great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 9, 2026
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023