Pay in installments of $82.11 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 3 - Aug 8
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Outer CV Joint MAP PRO Toyota Landcruiser 45 & 47 Series – MAP-100096Vehicle Fitment & Part Details This MAP Pro outer CV joint is engineered for Toyota Landcruiser 45 and 47 Series vehicles from 19731987. OEM references 4340560040 and 4430560040. Confirm compatibility by matching fitment details and VIN engine information before ordering. Key Details SKU MAP 100096 Component Outer CV Joint Brand MAP Pro Position Front Axle, Wheel Side Inner Splines 27 Outer Splines 30 Seal Diameter 62 mm Total Diameter 94 mm Length
Vehicle Fitment & Part Details
This MAP Pro outer CV joint is engineered for Toyota Landcruiser 45 and 47 Series vehicles from 1973–1987. OEM references 4340560040 and 4430560040. Confirm compatibility by matching fitment details and VIN/engine information before ordering.
Key Details
- SKU
- MAP-100096
- Component
- Outer CV Joint
- Brand
- MAP Pro
- Position
- Front Axle, Wheel Side
- Inner Splines
- 27
- Outer Splines
- 30
- Seal Diameter
- 62 mm
- Total Diameter
- 94 mm
- Length
- 241 mm
- Thread
- M8
- Groove
- Inside
- OEM References
- 4340560040, 4430560040 (Toyota)
- Primary Fitment
- Toyota Landcruiser 45 & 47 Series (1973–1987)
Vehicle Fitment
| Make | Model / Series | Years |
|---|---|---|
| Toyota | Landcruiser 45 Series | 1973–1987 |
| Toyota | Landcruiser 47 Series | 1973–1987 |
Fitment Notes
With CV joints, a VIN check can still return multiple possible variants. Confirm whether you need an inner CV joint, outer CV joint, CV boot, or complete driveshaft. Match the removed unit by outer spline count (30), inner spline count (27), seal size (62 mm), outer diameter (94 mm), groove position (inside), overall length (241 mm), and ABS ring tooth count where applicable.
Important: With CV joints and driveshafts, a VIN check can still return multiple possible variants within the same model range. First confirm whether you need an inner CV joint, outer CV joint, CV boot, or complete driveshaft. Then match the removed unit by outer spline count, inner spline count, seal size (mm), outer diameter (mm), groove position, overall length (mm), and ABS ring tooth count where applicable. The only reliable way to confirm the correct part is to physically inspect and measure the old unit and match these specifications before ordering.
Returns Notice: CV joints, driveshafts, and boots that are greasy or incomplete are not returnable.
Installation / Use / Maintenance Tips
- Always match OEM reference number(s) and vehicle details before ordering. Confirm exact fitment using VIN, engine code, or chassis number if multiple variants exist.
- Remove the old CV joint carefully, noting the orientation and any shims or spacers.
- Clean the shaft and inspect for corrosion, scoring, or damage before fitting the new joint.
- Apply fresh CV grease to the joint during installation; do not reuse old grease.
- Secure all fasteners to the torque specifications in the service manual.
- Check joint operation and listen for unusual clicking or knocking after installation.
Common Questions
Will this outer CV joint fit my Toyota Landcruiser 45 or 47?
Yes, this MAP Pro outer CV joint is designed for both the 45 and 47 Series (1973–1987). Verify fitment by matching the inner splines (27), outer splines (30), seal size (62 mm), and groove position (inside) to your removed unit.
What OEM part numbers match this CV joint?
This joint corresponds to Toyota OEM references 4340560040 and 4430560040.
Can I reuse the CV boot?
If the original boot is in good condition with no tears or grease loss, it may be reused. However, it is recommended to replace it alongside the joint for long-term reliability.
How do I confirm fitment if there are multiple variants?
Remove the old CV joint and physically measure and count: outer spline count (should be 30), inner spline count (should be 27), seal diameter (should be 62 mm), outer diameter (should be 94 mm), groove position (should be inside), overall length (should be 241 mm), and ABS ring tooth count if applicable. Match all these specifications before ordering to ensure correct fitment.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy